Changes
/* Advanced */
<span style="color:#FF0000">Warning: For advanced users only. Setting items to incorrect values may cause system to malfunction.</span>
==== Silicon Information PCIe/mSATA Configuration ====Processor and PCH signatures (example numbers):* '''FamilymPCIE1 Module''': 4th Gen Intel Core ProcessorSelect between mSATA and PCI Express interface on the shared slot. Default mSATA.* '''ModelUMI Gen2''': 45Enables/Disables <span style="color:#FF0000">TBD</span>* '''CPUIDFCH GPP OPTION''': 40651Enables/Disables <span style="color:#FF0000">TBD</span>* '''CPU REV.FCH GPP Port Link''': 1* '''PATCH ID'''* X4 mode: 17* '''CORE FREQ.'''* 2: 2.10 GHzmode:* '''L1 Cache'''* 2 1:1 mode: 64 KB* '''L2 Cache'''* 1:1:1:1 mode: 256 KB* '''L3 CachePSPP Policy''': 4096 KBPCIe speed power policy** Disabled** Performance** Balanced-High** Balanced-Low** Power Saving** Auto
Set hard drive and controller configuration:
* '''SATA DeviceConrtoller''': Enable/Disable SATA device. *'''Serial ATA Port i''': ** ''Port Enable'': Enable/Disable port i** ''External Port'': Configure the system to treat the port as internal or external** ''SATA Device Type'': Select 'Solid State Drive' only if SSD device is connected to port i ==== System Agent (SA) Configuration ====Displays and provides options to change the SA settings* '''Intel(R) VT for Directed I/O (VT-d)Mode''': Enables/Disables Intel Virtualization Technology for Directed I/O (VT-d) by reporting the I/O device assignment to VMM through DMAR ACPI tables* '''Graphics Configuration''': Graphics Configuration menu** '''DVMT Pre-Allocated''': Select pre-allocated graphics memory size used by the internal graphics device - 32MB, 64MB, 128MB, 256MB, 512MB.* '''IGD Configuration''':** ''IGD - Boot Type'': Select the primary video device activated during boot - DisplayPort, HDMI1, HDMI2** ''IGD - Secondary Boot Type'': Select the secondary video device activated during boot - HDMI1, HDMI2** ''IGD - Panel Scaling'': Select the LCD panel scaling option - Auto, Force Scaling, Off** ''Spread Spectrum Clock Chip'': Hardware - Spread is controlled by chip, Software - Spread is controlled by BIOS ==== South Bridge Configuration ====Set hard drive and SATA controller configuration:* '''SMBUS Device''': Enable/Disable SMBUS device* '''Enable CRID''': Enable compatible revision ID* '''State After G3''': Specify what state to switch to when power is re-applied after a power failure (G3 state).** State S0 - Active** State S5 - SW Off* '''mSATA-PCIe''': Switched between SATA legacy IDE and PCI Express interface on the full size mini PCIe slotAHCI modes. * '''SB PCI Express Config''': **'''PCI Express Root Port Clock Gating''': Enables/Disables PCI Express Root Port Clock Gating**'''DMI Link ASPM Control''': The control of Active State Power Management of DMI link**'''DMI Link Extended Sync Control''': The control of Extended Sync of SB side of the DMI link**'''PCI Express Port i Config''': Control the PCI Express Root Port i* '''SB USB Config''': Enables/Disables USB Port* '''SB Azalia Config'''** '''Azalia''': Control detection of the Azalia device** '''Azalia PME Enabled''': Enables/Disables PME for Azalia* '''SB Security Config'''** '''GPIO Lockdown''': Enable/Disable the PCH GPIO lockdown feature** '''RTC Lock''': Enable will lock bytes 38h-3Fh in the lower/upper 128-byte bank of RTC RAM ** '''BIOS Lock''': Enable/Disable the PCH BIOS lock enable feature. The whole BIOS region is not writable** '''SMM Lock''': Enable/Disable SMM lock feature. It will lock the SMRAM and unable load SMM driver any more.* '''Watchdog''': Enable/Disable Watchdog
==== Network USB Configuration ====* '''PCH Internal LANXHCI Controller''': Enable/Disable PCH internal LANXHCI HCs (Bus 0 Dev 16 Fn 0). When disable it that will active USB3.* '''LAN OPROM Selection''': This is used to select LAN OPROM for quick boot minimal configuration* '''Wake on PCH LANUSB1''': Enable PCH internal Wake on LAN capability at Moff/Disable USB1 HCs (Bus 0 Dev 18 Fn 0/2)* '''ASF SupportUSB2''': Enable/Disable alert specification formatUSB2 HCs (Bus 0 Dev 19 Fn 0/2)
==== SuperIO GFX Configuration ====SuperIO HD Graphics and Audio settings conrtol:* '''Onboard UART1Integrated Graphics''': Enabled always * '''Onboard UART2''': This option controls the onboard UART2 addressAuto/Disabled/Force - Enable integrated Graphics controller. When enabled UART2 uses address 0x2F8 and IRQ 3* '''Onboard UART3NB Azalia''': This option controls the onboard UART3 addressAuto/Disabled/Enabled - Enable integrated HD Audio controller. When enabled UART3 uses address 0x3E8 and IRQ 4
==== AMT Watchdog Configuration ====Configure Active Management Technology parameters:* '''Intel AMTWatchdog''': Enable/Disable watchdog timer.* '''AMT Wait TimerWatchdog count''': * '''SOL Terminal Type''': * '''Enter Intel MEBx Setup''': * '''UnSet Watchdog countdown timer, range between 15 sec-Configure ME''': * '''Hide Un-Configure ME Confirmation''': * '''USB Provision''': * '''MEBX Resolution Settings''': ** '''Non-UI Text Mode resolution''': ** '''UI Text Mode resolution''': ** '''Graphic Mode resolution''': 4 min.
=== Security ===
