Difference between revisions of "TEL-SERX4 technical documentation"
From fit-PC wiki
(→Configuration) (change visibility) |
(→Description) (change visibility) |
||
(16 intermediate revisions by 2 users not shown) | |||
Line 3: | Line 3: | ||
== Description == | == Description == | ||
− | TEL- | + | TEL-SERX4 Provides USB to Multiprotocol(RS-232, RS-485-Half Duplex, RS485-Full Duplex) serial connection (up to 4 Ports per TEL). |
* Simple USB Connection protocol | * Simple USB Connection protocol | ||
Line 13: | Line 13: | ||
− | USB <--> USB HUB <---> RS-232 / RS-485 - Native DB-9 Port | + | USB <--> USB HUB <---> RS-232 / RS-485 (Port A) - Native DB-9 Port |
− | RS-232 / RS-485 | + | RS-232 / RS-485 (Port B) |
− | RS-232 / RS-485 | + | RS-232 / RS-485 (Port C) |
− | RS-232 / RS-485 | + | RS-232 / RS-485 (Port D) |
RS-485 - Globally enable Termination resistor. - User Switchable | RS-485 - Globally enable Termination resistor. - User Switchable | ||
Line 22: | Line 22: | ||
− | TEL- | + | TEL-SERX4 is utilizing a USB2 interface |
− | Multiple TEL- | + | Multiple TEL-SERX4 cards can be installed in a system |
== Features == | == Features == | ||
Line 70: | Line 70: | ||
* Complete hardware design files are available | * Complete hardware design files are available | ||
* Complete firmware is available | * Complete firmware is available | ||
− | |||
== Connection requirements == | == Connection requirements == | ||
+ | === Pinout === | ||
+ | {| | ||
+ | |- | ||
+ | | [[File:TEL-SERDB9_DB9_pinout_diagram.png|thumb|none|600px | DB-9 Pinout]] | ||
+ | | [[File:TEL-SERDB9_DB9_Switch_board location.png|thumb|none|273px | Switch Location Diagram]] | ||
+ | |} | ||
+ | |||
=== Host interface === | === Host interface === | ||
USB2 | USB2 | ||
Line 81: | Line 87: | ||
== Version information == | == Version information == | ||
− | Latest HW Version Rev 1. | + | Latest HW Version Rev 1.1 |
==Block diagram== | ==Block diagram== | ||
− | |||
− | |||
== Mechanical model == | == Mechanical model == | ||
Line 95: | Line 99: | ||
== Software source files == | == Software source files == | ||
− | |||
ToDo add files | ToDo add files | ||
− | + | ||
+ | Example script for controlling I2C ?? |
Latest revision as of 15:00, 15 November 2020
Contents
Compulab part number
FT.H-SER4
Description
TEL-SERX4 Provides USB to Multiprotocol(RS-232, RS-485-Half Duplex, RS485-Full Duplex) serial connection (up to 4 Ports per TEL).
- Simple USB Connection protocol
- Supports Multiprotocol implementation on one DB9 Connector.
- Individually enabled between RS-232 or RS485 ports.
- Build-in Termination resistor.
- Protocol switching using Onboard switches or using I2C expander
USB <--> USB HUB <---> RS-232 / RS-485 (Port A) - Native DB-9 Port RS-232 / RS-485 (Port B) RS-232 / RS-485 (Port C) RS-232 / RS-485 (Port D)
RS-485 - Globally enable Termination resistor. - User Switchable - Globally Switched Between Half Duplex and Full-Duplex mode. - User Switchable
TEL-SERX4 is utilizing a USB2 interface
Multiple TEL-SERX4 cards can be installed in a system
Features
- Serial through DB-9 Connector
- Implemented using FTDI FT4232H
Software
- Windows and Linux support
- Driverless operation in Windows & Linux
- USB native device in Linux
Electrical and environmental
- Ambient Operation from –40°C to 85°C.
Configuration
- Two Configuration method of the device
- Onboard switches
SW1 - PORTA: ON->RS-232 OFF->RS-485 - Native on board Port SW2 - PORTB: ON->RS-232 OFF->RS-485 SW3 - PORTC: ON->RS-232 OFF->RS-485 SW4 - PORTD: ON->RS-232 OFF->RS-485 SW7 - ON->RS-485 Half Duplex OFF->RS-485 Full-Duplex - Port A-D SW5 - ON->Enables Termination resistor RS-485-Half Duplex - Port A-D SW6 - ON->Enables Termination Resistor RS-485-Full Duplex - Port A-D
- I2C GPIO expander(PCA9555) that is located on I2C address 0X27.
I/O,0.0 -- Port A: High: RS-232, Low: RS-485 I/O,0.1 -- Port B: High: RS-232, Low: RS-485 I/O,0.2 -- Port C: High: RS-232, Low: RS-485 I/O,0.3 -- Port D: High: RS-232, Low: RS-485 I/O,0.4 -- NC I/O,0.5 -- NC I/O,0.6 -- NC I/O,0.7 -- Global: High RS-485 Half Duplex, Low: RS-485 Full Duplex
I/O,1.0 -- Port A: High RS-485 Termination enabled on Half Duplex Lines I/O,1.1 -- Port B: High RS-485 Termination enabled on Half Duplex Lines I/O,1.2 -- Port C: High RS-485 Termination enabled on Half Duplex Lines I/O,1.3 -- Port D: High RS-485 Termination enabled on Half Duplex Lines I/O,1.4 -- Port A: High RS-485 Termination enabled on Full-Duplex Lines I/O,1.5 -- Port B: High RS-485 Termination enabled on Full-Duplex Lines I/O,1.6 -- Port C: High RS-485 Termination enabled on Full-Duplex Lines I/O,1.7 -- Port D: High RS-485 Termination enabled on Full-Duplex Lines
Open source hardware and software
- Complete hardware design files are available
- Complete firmware is available
Connection requirements
Pinout
Host interface
USB2
Physical connection
or
Version information
Latest HW Version Rev 1.1
Block diagram
Mechanical model
ToDo: Add 3D model
Hardware design files
ToDo: Add Gerbers ToDo: Add Schematics
Software source files
ToDo add files
Example script for controlling I2C ??