Changes

** '''Port Enable''': Enable/Disable port i** '''External Port''': Configure the system to treat the port as internal or external** '''SATA Device Type''': Select 'Solid State Drive' only if SSD device is connected to port i

Displays and provides options to change the SA settings* '''TBDIntel(R) VT for Directed I/O (VT-d)''': Enables/Disables Intel Virtualization Technology for Directed I/O (VT-d) by reporting the I/O device assignment to VMM through DMAR ACPI tables* '''TBDGraphics Configuration''': Graphics Configuration menu* * '''TBDDVMT Pre-Allocated''': Select pre-allocated graphics memory size used by the internal graphics device - 32MB, 64MB, 128MB, 256MB, 512MB.* '''IGD Configuration''':** ''IGD - Boot Type'': Select the primary video device activated during boot - DisplayPort, HDMI1, HDMI2** ''IGD - Secondary Boot Type'': Select the secondary video device activated during boot - HDMI1, HDMI2** ''IGD - Panel Scaling'': Select the LCD panel scaling option - Auto, Force Scaling, Off** ''Spread Spectrum Clock Chip'': Hardware - Spread is controlled by chip, Software - Spread is controlled by BIOS

Set hard drive and controller configuration:* '''TBDSMBUS Device''': Enable/Disable SMBUS device* '''TBDEnable CRID''': Enable compatible revision ID* '''State After G3''': Specify what state to switch to when power is re-applied after a power failure (G3 state).** State S0 - Active** State S5 - SW Off* '''mSATA-PCIe''': Switched between SATA and PCI Express interface on the full size mini PCIe slot. * '''SB PCI Express Config''': **'''PCI Express Root Port Clock Gating''': Enables/Disables PCI Express Root Port Clock Gating**'''DMI Link ASPM Control''': The control of Active State Power Management of DMI link**'''DMI Link Extended Sync Control''': The control of Extended Sync of SB side of the DMI link**'''PCI Express Port i Config''': Control the PCI Express Root Port i* '''SB USB Config''': Enables/Disables USB Port* '''SB Azalia Config'''** '''Azalia''': Control detection of the Azalia device** '''Azalia PME Enabled''': Enables/Disables PME for Azalia* '''SB Security Config'''** '''GPIO Lockdown''': Enable/Disable the PCH GPIO lockdown feature** '''RTC Lock''': Enable will lock bytes 38h-3Fh in the lower/upper 128-byte bank of RTC RAM ** '''BIOS Lock''': Enable/Disable the PCH BIOS lock enable feature. The whole BIOS region is not writable** '''SMM Lock''': Enable/Disable SMM lock feature. It will lock the SMRAM and unable load SMM driver any more.* '''TBDWatchdog''': Enable/Disable Watchdog

* '''TBDPCH Internal LAN''': Enable/Disable PCH internal LAN* '''TBDLAN OPROM Selection''': This is used to select LAN OPROM for quick boot minimal configuration* '''TBDWake on PCH LAN''': Enable PCH internal Wake on LAN capability at Moff* '''ASF Support''': Enable/Disable alert specification format

SuperIO settings conrtol:* '''TBDOnboard UART1''': Enabled always * '''TBDOnboard UART2''': This option controls the onboard UART2 address. When enabled UART2 uses address 0x2F8 and IRQ 3* '''TBDOnboard UART3''': This option controls the onboard UART3 address. When enabled UART3 uses address 0x3E8 and IRQ 4

Configure Active Management Technology parameters:* '''TBDIntel AMT''': * '''TBDAMT Wait Timer''': * '''TBDSOL Terminal Type''': * '''Enter Intel MEBx Setup''': * '''Un-Configure ME''': * '''Hide Un-Configure ME Confirmation''': * '''USB Provision''': * '''MEBX Resolution Settings''': ** '''Non-UI Text Mode resolution''': ** '''UI Text Mode resolution''': ** '''Graphic Mode resolution''':

Configure Management Engine Technology parameters:* ME FW Version 9.5.30.1808* ME Firmware Intel ME 5MB firmware* '''Intel ME''': * '''TBDIntel AT''': * '''TBDME FW Downgrade''': * '''TBDME IFR Feature''':

Thermal control sub-menu:* '''TBDCPU Thermal Configuration''': * '''TBDBi-directional PROCHOT#''': * '''TBDPROCHOT# OUT''': * '''PROCHOT Response''': * '''Disable VR Thermal Alert''': * '''ACPI 3.0 T-States''':