Difference between revisions of "IPC2B: USB3.0 Driver Installation Guide"
From fit-PC wiki
Line 4: | Line 4: | ||
==Instructions== | ==Instructions== | ||
1. Install the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_Chipset.zip Chipset driver] before the USB3.0 driver | 1. Install the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_Chipset.zip Chipset driver] before the USB3.0 driver | ||
+ | |||
2. Download the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_USB30.zip USB3.0 driver] | 2. Download the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_USB30.zip USB3.0 driver] | ||
+ | |||
3. Extract the downloaded package | 3. Extract the downloaded package | ||
+ | |||
4. Run the '''OfflineSetup32.exe''' file for Windows 7 32bit or the '''OfflineSetup64.exe''' file for Windows 7 64bit | 4. Run the '''OfflineSetup32.exe''' file for Windows 7 32bit or the '''OfflineSetup64.exe''' file for Windows 7 64bit | ||
+ | |||
5. Follow the on-screen instructions | 5. Follow the on-screen instructions | ||
+ | |||
6. At the the end of installation process, reset the unit | 6. At the the end of installation process, reset the unit | ||
+ | |||
7. Enter the BIOS menu by pressing the '''[F2]''' key during boot | 7. Enter the BIOS menu by pressing the '''[F2]''' key during boot | ||
+ | |||
8. Browse to | 8. Browse to | ||
Advanced | Advanced | ||
Line 16: | Line 23: | ||
set '''xHCI Mode''' to '''[Enabled]''' | set '''xHCI Mode''' to '''[Enabled]''' | ||
9. Press the '''[F10]''' key for Save&Exit | 9. Press the '''[F10]''' key for Save&Exit | ||
+ | |||
10. When Windows bootd up, open the downloaded package | 10. When Windows bootd up, open the downloaded package | ||
+ | |||
11. Run the '''Setup.exe''' file | 11. Run the '''Setup.exe''' file | ||
+ | |||
12. Follow the on-screen instructions | 12. Follow the on-screen instructions | ||
+ | |||
13. At the the end of installation process, reset the unit | 13. At the the end of installation process, reset the unit | ||
+ | |||
[[Category:IPC2]] | [[Category:IPC2]] | ||
[[Category:software]] | [[Category:software]] | ||
[[Category:Application notes]] | [[Category:Application notes]] |
Revision as of 13:51, 15 October 2018
- This application note provides a step by step guide to install USB3.0 drivers over Windows 7.
- Applicable to IPC2-Broadwell machines.
Instructions
1. Install the Chipset driver before the USB3.0 driver
2. Download the USB3.0 driver
3. Extract the downloaded package
4. Run the OfflineSetup32.exe file for Windows 7 32bit or the OfflineSetup64.exe file for Windows 7 64bit
5. Follow the on-screen instructions
6. At the the end of installation process, reset the unit
7. Enter the BIOS menu by pressing the [F2] key during boot
8. Browse to
Advanced South Bridge Configuration SB USB Config Menu. set xHCI Mode to [Enabled]
9. Press the [F10] key for Save&Exit
10. When Windows bootd up, open the downloaded package
11. Run the Setup.exe file
12. Follow the on-screen instructions
13. At the the end of installation process, reset the unit